parts that inter change with TRI-Z 250

[Tri-Z Pilot]

Really? Sorry about that, I saw them on another tri-z, and thought they looked pretty good. scratch that then, good head heads up chainsaw.

[BigGreenMachine]

Where did you see the Tri-z with the Raptor fenders? I'd like to see it.

[TRI-Zbrian]

is that true if you use 200x hubs that they will give you an extra 2 inches?? i might have to try that out my buddy has a crap load of x stuff kicken around. also i have updated it guys with what has been said so far but i will wait on the 200x hubs deal till i get more info on that is it true you will get an added 2 inches by using the 200x huns??

[J.D.]

Oh don't forget the 85 YZ250 head gasket, now *I'VE HEARD* that it's thinner so it adds more compression, like the ATC250R/CR250 head gasket trick. I don't think the base gaskets are the same.

[slippy4]

yes, but they have to be the 86-87 hubs. ive heard they fit a little tight but do fit.

[TRI-Zbrian]

thanx ive added all of that also

on a side note what other shocks bolt up or will bolt up with miner mods? so i can add those as well

[CHAINSAW]

Really? Sorry about that, I saw them on another tri-z, and thought they looked pretty good. scratch that then, good head heads up chainsaw.

np man. there was a pair on a Tri Z on ebay a while back, so I bought a pair to put on mine. There was only one pic of the bike, and for good reason. They look good from a side profile, but when you get up close, it looks like crap. I had to make a cover for that back part. There is a 8 inch gap behind the seat where the plastic ends. I have a pair of fenders allready cut and modified to fit a Tri Z if anyone is interested. Id need $40 for them, cause thats what I have in them (pm me if interested, Ill give all the details)

[Trikeaholic]

how about brake calipers???

[TRI-Zbrian]

yeah guys i know there are alot more parts out there that will bolt up what about those other kinds of shocks that will bolt up or bolt up with miner mods

[Darius1502]

I may have missed this on the list...but does'nt the Banshee rear brake calipher fit on the Tri-Z?

Also the 85 BW front fender will fit the Z, but not the 86 BW front fender. Also I have heard that the headlight from a 350x will fit and I have a pic on my old Dirt Wheels of the Tri-z with an 85 ATC 250R head light on it. Looks pretty good actually.

I have heard also that the YZ490 motor bolts into the frame and since the WR 500 was about the same motor then that powerplant will probably bolt in as well.

I know I am getting off topic but just thought I would throw these out there.

[TRI-Zbrian]

ive got the caliper deal on there its towards the bottom also thanx for the info ive updated my post with your info except of the engines interchangeability because i dont know if it a fact or not yet

[redrider77x]

i think i heard somewhere that the banshee clutch is the same? not shure

[marshallfester^australia]

You guys are starting to give me a bit of faith in the TRI-Z 250, always though they where a great looking trike but parts just can not be found over here real easy, well eerrrr not at all!, but with this post and the donor parts you have shown that can be used it may just swing me towards a TRI-Z 250 one day!!!!!!!!

[xtremez]

how about a husqvarna chain tensioner? has that been added to the list.Dont know what years just seen it done

[twgranger]

how about a husqvarna chain tensioner? has that been added to the list.Dont know what years just seen it done

The person who started this thread is missing in action and i think wanted so i dont think anything is going to be added to the list.