I have an 83 185s that i would like to put the rear hubs off my 85 250es on. Can anyone tell me if they will swap. The bikes are thirty minutes away and I wont be over there for a couple days.
At The Back Of The Pack
Arm chair racerAt the back of the pack
I have an 83 185s that i would like to put the rear hubs off my 85 250es on. Can anyone tell me if they will swap. The bikes are thirty minutes away and I wont be over there for a couple days.
1. 83 185s: (the money pit) xr200 cam, 200cc cylinder, 10.25:1 piston, 83 250r front end, 450r hubs, full suspension
2. 85 Big Red 250es: in pieces
3. 85 200m
4. 00 Polaris Magnum 325 2x4: stays broke
5. 02 Yamaha Wolverine 350 4x4: trail bike
Power User
The day begins with 3WW
i can say not a chance, the machines are so far apart the 185 sports a solid chain driven axle with traditional hubs but the 250es has the outer axle tube seals as part of the hubs so your answer is not a chance.
ok here goes, 85 atc70,2 84 atc70's 83 alt50,83 atc110 , 70 us 90 parot green, 85/86 350x garage queen, stock rider 85 350x, project 85 350x 85 250r drag bike, 2 85 250sx's, alt185, , scat tracker?99blaster,85 250r rider,85 250r ice racer project ,93 kx500,99 xr200r, 91 dr250s ,89 lt500 quadzilla,88 lt250quadracer, 88 trx250r race full on race quad,, 01 yamahakodiak400, kawaki kd100,lt50 for my doughters,93 300ex, 230 quadsport, lt185, lt250 quadrunner,84200s, is that enough?
New to the board
Arm chair racerNew to the board
buy a pair of 400ex hubs. the spline is the same and they also offset your wheels a bit. You aso get a more popular 4x110 bolt pattern. i just bought a brand new set on ebay for $110 shipped to my door. you can get them cheaper but i didnt want to risk it on a used set for my build
Power User
4 Wheels? Huh?
So the 400EX hubs fit most of these 185/200cc trikes then? I was thinking this for my 200m.Originally Posted by ShaneNP123
Current toys..
1986 Honda 350X..trail bomb!
1985 Honda 250SX..my main mudder
1985 Honda 250ES..Back in Black Trike
Current non-trike toys:
1990 Honda TRX300FW
1995 Seadoo GTX
1998 Polaris Indy Lite 340(Nearly new looking)
1998 Polaris Touring 500
1998 Club Car (electric)
At The Back Of The Pack
Arm chair racerAt the back of the pack
Thanks I didn't think they would fit but it would have been great if they did. And thanks for the 400ex tip I am looking to get the 4/110 bolt pattern because I have some nice mudders on my 250es that I want on my 185s because the 250es will be out of commission for a while. Is the 400ex the only other hub or are there any others and what is the most abundant that will fit.
1. 83 185s: (the money pit) xr200 cam, 200cc cylinder, 10.25:1 piston, 83 250r front end, 450r hubs, full suspension
2. 85 Big Red 250es: in pieces
3. 85 200m
4. 00 Polaris Magnum 325 2x4: stays broke
5. 02 Yamaha Wolverine 350 4x4: trail bike
Power User
Got the holeshot
TRX 400ex, 450R, 300ex, 250x, etc = all the same hub.
$30-$50 a pair shipped on eBay
Be sure you get them with studs. Buying and installing studs just adds cost and time and they're too cheap and plentiful to deal with that crap.
Lug nuts are a nice bonus, too.
For example...
http://www.ebay.com/itm/TRX400ex-REA...sories&vxp=mtr
http://www.ebay.com/itm/Honda-450R-R...sories&vxp=mtr
http://www.ebay.com/itm/03-Honda-TRX...sories&vxp=mtr
Power User
4 Wheels? Huh?
And all these will fit the 185/200 machines? Or are there some these won't fit??..just to be clear.
Current toys..
1986 Honda 350X..trail bomb!
1985 Honda 250SX..my main mudder
1985 Honda 250ES..Back in Black Trike
Current non-trike toys:
1990 Honda TRX300FW
1995 Seadoo GTX
1998 Polaris Indy Lite 340(Nearly new looking)
1998 Polaris Touring 500
1998 Club Car (electric)
Power User
Got the holeshot
400ex/450R etc hubs bolt on the 70/90/110/125/185/200 families. I had a pair on my 84 200X. Fit 250 Odyssey, too.
Do not bolt on 85/86 250R, 350X and 2nd gen 200X.
I don't know squat about the shafties - 250ES, SX, etc but assume no way they'll fit as stated above.
At The Back Of The Pack
Arm chair racerFirst time rider
Hey, I have them on my 86 200X...
Taming the three wheeled beasts since 1980.
My Feedback:
http://www.3wheelerworld.com/showthr...ayspowersports
Power User
Got the holeshot
Oh - I ASSumed those had the same splines as the 250R/350X. Now I know - THANKS!
Just Too Addicted: Protecting Our Community
The day begins with 3WW
This info compliments of Howdy in a previous axle/hub thread:
I have TRX450R hubs on my 200S with 200X rims.The axle splines on these machines are the same ( the hubs are different bolt pattern than others ):
ATC70
75-78 ATC90
ATC110
ATC125m
ATC185
ATC185s
ATC200
ATC200e
ATC200es
ATC200m
ATC200s
83-87 ATC200x 4/110 ( 86-87 style set the tires 2" out per side. 4" total added width )
81-84 ATC250r
1986-87 Tecate
And these 4 wheelers ( That I personally know fit ):
200sx
300ex 4/110
400ex 4/110
I know there are others but can't think of them right now.
Howdy
Liberalism suspends the intellect of its victims, while at the same time tricking them into believing that they're smarter than everyone else.
If we've done business together, please leave me feedback. Thank You!:
http://www.3wheelerworld.com/showthr...t=Scootertrash
At The Back Of The Pack
Arm chair racerFirst time rider
1986 tr200 Fatcat
1985 ATC250es, all original but tires, need a right side cover
1983 ATC200e All original but tires and wheels
DG pipe, uni filter, jetted
1983 KLY250C Prairie (for sale as parts)
1982 ATC70 (x3)
Reply With Quote
