My 83 250R Project

[freestylejunki3]

Well it is far from done , but it is lookin much better already than when i got it. Right now i need to get my swingarm pivot bolt fixed so i can put the rear end on. Then its just a matter of saving the money to buy the bits and peices...let me know what u think.

http://i692.photobucket.com/albums/vv281/freestylejunki32/DSC01451er.jpg

http://i692.photobucket.com/albums/vv281/freestylejunki32/DSC01455.jpg

http://i692.photobucket.com/albums/vv281/freestylejunki32/DSC01457.jpg

[theiizz08]

lookn good so far

[beets442]

Looks good.. Make sure you check the frame for cracks... Beets

[aaron7]

You should sell me those plastic pieces under the gas tank :D

[harryredtrike]

looks good so far.what paint did you use rustolium?:Bounce

[freestylejunki3]

ya i believe it was rustoleum...not tryin to make a show peice tho...just something that looks decent and rides better :) Now i gotta get my hands on an new pivot bolt for the swingarm when i get some money.

[freestylejunki3]

Well i got the tank cleaned up and finished painting it.
http://i692.photobucket.com/albums/vv281/freestylejunki32/TankPainted5-13-2009.jpg



Plus i just picked up this motor off from ebay for $330. Comes with all the electronics, twist throttle, kicker and shift lever. Not a bad deal i dont think.
http://i692.photobucket.com/albums/vv281/freestylejunki32/newengine.jpg

http://i692.photobucket.com/albums/vv281/freestylejunki32/250r.jpg

I have some swingarm pivot bushings coming soon. Then soon as i get a new pivot bolt i can put the rear end all together. What do you guys think so far???

[aaron7]

Haha, I was bugging that seller to sell me the chain guard off that motor. Good deal, definately.

[mpwrd3]

Looks good!

[SYKO]

great start, that motor was a good deal (if its running) for that price!

[freestylejunki3]

great start, that motor was a good deal (if its running) for that price!


Well the descrption says that it runs mint and starts first kick every time, no scores on piston or sleeve and a very strong runner...so it better run well. Ill let you know how it works out and get some pics up when its in

[freestylejunki3]

Well i got the engine yesterday and stuffed it into the frame. I dont have the motor mounting bolts yet so i just stuck some smaller bolts in to hold it in place. I havnt started it yet but so far it seem just like the description...the piston and sleeve look good, good compression. i turned the gears over by hand and it shifts through all of them. The electronics work well...has a good strong spark. Now i just need to get ahold of some mounting bolts and find a head pipe so i can start this thing up. Honda shop want $50 for OEM engine bolts. I think ill try my luck on ebay.

http://i692.photobucket.com/albums/vv281/freestylejunki32/DSC_1495.jpg

http://i692.photobucket.com/albums/vv281/freestylejunki32/DSC_1496.jpg

http://i692.photobucket.com/albums/vv281/freestylejunki32/DSC_1497.jpg

[rdlsz24]

Lookin good

Rob

[Lukeatc185]

instead of ebay, id try using a steel company, here in ontario we have Brafasco, i got all my engine bolts and even some of the smaller screws needed for my carb because the old ones were stripped, i payed 6.75 for all of them lol.

[lookinforone]

lookin good.
try this (http://www.fastenal.com/web/home.ex) for the bolts.

[MonroeMike]

That's coming along great. You're gonna have a decent ride.

[freestylejunki3]

Well i just got the new bearings in the front and rear end. Installed my axle...its almost starting to look like a 3 wheeler...wut do you think?

http://i692.photobucket.com/albums/vv281/freestylejunki32/6-6-2009-1.jpg

http://i692.photobucket.com/albums/vv281/freestylejunki32/6-6-2009.jpg