Question for the 350X crowd

[Hoosier_Daddy]

Just wondering if any of you have dealt with these guys or have heard anything about them? They offer the top end kits for the 350X on ebay. Is this a decent price for what they are offering?

http://cgi.ebay.com/ebaymotors/Honda-Atc-350X-350-X-Engine-Motor-Top-End-Rebuild-Kit_W0QQcmdZViewItemQQ_trkparmsZ72Q3a570Q7c66Q3a2Q 7c65Q3a12Q7c39Q3a1Q7c240Q3a1318Q7c301Q3a0Q7c293Q3a 1Q7c294Q3a50QQ_trksidZp3286Q2ec0Q2em14QQhashZitem2 60301679162QQitemZ260301679162QQptZMotorsQ5fATVQ5f PartsQ5fAccessories

[Extremesounds13]

I have dealt with them a couple times. I have never bought that particular item from them but everything I have bought has been great and they shipped way quick..... hope that helps some; oh and it does look like a nice price!

[Hoosier_Daddy]

Thanks for the input. It does look like a great price. Mine really isn't in dire need of a rebuild but for that price, i might just go ahead and do it.

[Vealmonkey]

I've had good luck from them too in the past. My only concern is if you received a cylinder that was on it's last overbore. I don't know if there is any way to control that.

[hrc200x]

I'm in the process of dealing with them right now with a 350x rebuild. I sent my cylinder to them, they machine that one and send it back, I thought it might have been an exchange program to, but doesn't sound like it, for the 350x atleast. I shipped him the cylinder on march 4th and I'm expecting it anyday.

Am also getting a 350 head done. I was quoted $180 for a 350 head which included, blasting it, new valves, regrind head, check specs on valve guides and springs, new seals and finally vaccumme testing to make sure everything is sealed.

[SWIGIN]

i dont think its a screaming deal, it sounds about right to me as far as price.

cheap ebay gaskets, local bore job, new piston can be had for cheaper but not much.

[tri-Z ripper]

would be interested in the outcome as well! though about it for the 200X but wasn't sure about the exchange as well. compared to locally dropping it off and picking it up!!

[The Goat]

100 bucks for a piston, 30 bucks for a bore, 30 bucks for a gasket kit.

notice you're only at 160 bucks...

[Hoosier_Daddy]

Thanks for the input guys. I'll check with some local shops and see how much they would charge to bore it around here. Not many machine shops like that left around her anymore. Cycle shops want an arm and a leg for any kind of work they perform.

[atctim]

Guys - please post ebay stuff in the ebay forum - this is not where it belongs!

[Hoosier_Daddy]

Guys - please post ebay stuff in the ebay forum - this is not where it belongs!I thought the ebay forum was for selling or buying postings from Ebay. Sorry, i didn't realize this had to go there.

This thread isn't about Ebay, though. I just wanted input on the cost and quality of someones work. It just so happenes they use ebay to sell their service.

[3Razors]

Do a compression check. If the motor runs great, doesn't smoke, ect. I would just run it. No need to waste money on a rebuild if it doesnt need it. Honda motors run forever with even the basic maintenance.

[hrc200x]

I think its a good deal going on this info. In dennis kirk just the top end gasket set from vesrah is $52. Wiseco 10.25:1 piston $132. So thats $184 total. That leaves $25 for labor to clean and bore. Shipping for me was about $14 each way which sucks, but the work did get done faster than if my local guy did it. Maybe the piston and gasket set is available cheaper somewhere else? If so point me in the direction.

I'm assuming the gaskets in the pic are vesrah. I ordered a cheap kit once and it didn't have that large o ring for the bottom of the cyclinder, this vesrah complete kit I just bought to do this rebuild did have it.

[Howdy]

100 bucks for a piston, 30 bucks for a bore, 30 bucks for a gasket kit.

notice you're only at 160 bucks...

I agree 100%, I think they are a little high in price. But then I can get my personal stuff at wholesale. ;)
Howdy

[Louis Mielke]

Well I know here between 3 local shops, they all want $50 for the first bore, don't even ask about bigbores. The price gets stupid quick.

[hrc200x]

Cylinder came lastnight, gaskets arn't vesrah, but armor tech.