200es top end

[roberttice]

What piston kit will fit the 200es. I have seen several kits on eBay and was wondering which ones will work. Also can you bore the 200 out and make it a 250 or is this not practical.

[jaykup]

Most of the ATC 200 pistons will fit, stock size is 65mm, and can go up to 67mm (2mm over). Check what piston is in there now, so you don't buy one too small. Stock for stock, the 200x has a higher compression ratio, but all the Wiseco pistons are 10.25:1

OEM Matches are:
ATC185 '80
ATC185s/200 '81-'83
ATC200ES '84 BIG RED
ATC200M '84-'85
ATC200S '84-'86
TRX200 '84
ATC200E '82-'83 (BIG RED)

Something like this will work: http://cgi.ebay.com/ebaymotors/Honda-atc200S-atc-200-wiseco-080-over-piston-kit-84-86_W0QQcmdZViewItemQQcategoryZ43977QQihZ016QQitemZ 260208121732QQrdZ1QQsspagenameZWD1VQQtrksidZp1638Q 2em118Q2el1247

Displacement is as follows:

Bore x Stroke
65 x 57.8 Stock = 192cc
66 x 57.8 1mm over = 198cc
67 x 57.8 2mm over = 204cc

[84honda200s]

Most of the ATC 200 pistons will fit, stock size is 65mm, and can go up to 67mm (2mm over). Check what piston is in there now, so you don't buy one too small. Stock for stock, the 200x has a higher compression ratio, but all the Wiseco pistons are 10.25:1

OEM Matches are:
ATC185 '80
ATC185s/200 '81-'83
ATC200ES '84 BIG RED
ATC200M '84-'85
ATC200S '84-'86
TRX200 '84
ATC200E '82-'83 (BIG RED)

Something like this will work: http://cgi.ebay.com/ebaymotors/Honda-atc200S-atc-200-wiseco-080-over-piston-kit-84-86_W0QQcmdZViewItemQQcategoryZ43977QQihZ016QQitemZ 260208121732QQrdZ1QQsspagenameZWD1VQQtrksidZp1638Q 2em118Q2el1247


Displacement is as follows:

Bore x Stroke
65 x 57.8 Stock = 192cc
66 x 57.8 1mm over = 198cc
67 x 57.8 2mm over = 204cc





you use to be able to get a wisco 12:1 200 piton from dennis kirk. but i dont know if they still offer it. dont forget there are some dirt bikes that use the same piston too. ill have to look em up and post them later. i thnk the xr200 is one and a couple other xr bikes as well.










i am currently running a 67mm wisco 10.25:1 piston. runs strong but it isnt a treat to try and pull over with the recoil. but none the less its a noticeable difference. i now have allot of other mods done but i think the bore,better compression, bigger carb, and bassani exhaust were the key mods.



ooo and no you cant bore it to a 250. the cylinder walls just arnt thick enough. if it had thicker walls yea it might work.

[TeamGeek6]

Wiseco has 10.5 and 12:1's. for 200X

[choppertown]

so from what i gather here, a 200s(81-86) piston will fit into a 84 200ES. ?

[rdlsz24]

Yes the top ends are interchangeable on all the 185/200 utility trikes and 83-85 200x

Rob

[84honda200s]

so from what i gather here, a 200s(81-86) piston will fit into a 84 200ES. ?

yep just gotta make sure the bore is the same .. but if you gunna swap out the top ends yes all the 185/200 cylinders and heads will fit a 185/200 bottom end ..

[choppertown]

no just my parts dealer can get me a cheap 200s piston

[TheRealFatShady]

Displacement is as follows:

Bore x Stroke
65 x 57.8 Stock = 192cc
66 x 57.8 1mm over = 198cc
67 x 57.8 2mm over = 204cc

This is some good info to have. Not sure why everyone thinks boring gives many more cc's????

What exactly does the compression ratio *(ie a 12 to 1 piston over stock) change? Is there any way to increase CC or any larger cylinders that may fit?

[choppertown]

yea the thing hasnt been bored over. my supler just has a 200s piston in 10.25 comp and 12:1 comp i can get for cheap. but dnt have any wisco pistons for the 200ES

[TheRealFatShady]

12:1 I would want, any chance you can tell me how much in a PM? (have rings with it?)