Are these NOS 110 fenders or something else????????????

[LonesomeTriZ]

I recently bought these Maier fenders from an accessory shop in Tennessee. The guy up there told me they are for a Honda ATC 110. Some of the members here said they are not. Can some one here tell me what they are for?

[Tri-ZNate]

those look like 70 fenders. The 110 are 1 piece.

[82300R]

i have two 1980 110's with the original fenders. they do not look like yours. my sons 1985 70 fenders dont look like those either. hope that helps some.

[LonesomeTriZ]

well, it looks like I am getting closer. Any other ideas at all?

[old honda dealr]

I say looks like the 73 ATC 70 fenders. They are a 2 piece like that. There was one on ebay that you could look at for a reference

[Tri-ZNate]

They dont look like M or es fenders so i'd say they are early 70cc fenders.

[thefox]

The only trike fenders those could be are the early Honda 70 rear fenders. Could they be quad fronts or maybe Pilot fenders?

[LonesomeTriZ]

I just found a number on the corner. i'll see if I can write it down and find out what it means.

[Howdy]

The only trike fenders those could be are the early Honda 70 rear fenders. Could they be quad fronts or maybe Pilot fenders?

While they do look simular to the 73 ATC70 fenders, they are probably from a Quad. I say this because I don't think maier makes replacement fenders for the 73 ATC70. But I could be wrong.
Howdy

[LonesomeTriZ]

These fedners are really old. So they may have at one time.

by the way, what is the item number for that auction?

[crd00]

Those are definetly 70 fenders because most of the higher cc trikes have one pieces

[LonesomeTriZ]

I am assuming this is the right side fedner. The number stamped on the inside is 11728RH.

The left is 11728LH

How can I sue these numbers to know for sure?

[DeePa]

emailer maier with those numbers

[82300R]

if they are maiers, i would try to contact them with those numbers an see if something comes up. maybe they can do that.

[82300R]

emailer maier with those numbers
yeah what he said!:lol: :lol:

[LonesomeTriZ]

I was hoping I could find a parts list from them but no luck from my internet search. The last time I tried to get some information through them about three wheeler parts the person I was talking to acted like I shot his cat. appaerently they do not like to admit to their three wheeler history.

[LonesomeTriZ]

I just performed one hell of a search and found nothing. Maybe I am looking in the wrong areas. Do any of you have any suggestions other than calling? I'll call later on in the week if I can not find anything this way.

[Lomax]

What are the measurements of them? ITs hard to tell in the pictures. They could be early ATC200 but they do look small. I'll find a set of the old 200 fenders around here and give you call in a day or 2 and see if we can figure it out. That will give you time to get a tape measure rounded up and me time to acutally find a set if there's any still around here. I dont know of any quad with a split fender so I am still leaning on them being ATC.

[Lomax]

What a minute. I found my Maier listings and this is strange The part number 11728 in here does not show a left or a right but its shows the be the front for a 87-92 TRX250X. It says that they are an Add-On. Now I dont know what in the hell that means. I know they dont look like a 250X fender much to me so maybe they recycled the part number?? I am using a suppliers catalog so they might be the wrong number all together. I'll call them, if they still have them then I'l make them take a look and describe them to me.
-Will

[LonesomeTriZ]

Well I will be damned. I hope I can find a buyer for them.