kilabeez0 lets see how your project is going

[vartiak15]

can we get some pics of your project so far? what mods are you doing to the 200x?

[kilabeez0]

sure i'll snap a few in a couple minutes.

[kilabeez0]

http://images.ofoto.com/photos868/4/63/33/4/27/0/27043363406_0_ALB.jpg http://images.ofoto.com/photos868/4/63/23/95/90/0/90952363406_0_ALB.jpg

[kilabeez0]

how come it only shows 2 pics, and if i reply with more they only come up as X's?

[BigGreenMachine]

i cannot see the pics

[kilabeez0]

u can"t, i can see them? if u see a red x, right click and hit show picture.

If that doesn't work someone try this link and post them for me.

http://www.ofoto.com/BrowsePhotos.jsp?Uc=17zalnqi.lm0ejim&Uy=-5ahiil&Ux=1&collid=47043363406

If you have to join it's free and only takes a second. I dont get it though. I highlight the picture, right click it, go to properties, and then highlight the pictures address, copy it, and paste it here in the prompt for a picture. Why doesn't it work?

[BigGreenMachine]

oh cool, i see them on trailprotrailpro photo page, nice job, thats bout where my Tecate project is right now.

[smokinp]

good job! :TrikesOwn

[kilabeez0]

things that are new

white front fender
seat cover (not put on yet)
honda piston first bore over
BRAND NEW honda cam, bushing, cotter pin
valve seals and valve job
sprockets front and back
plate that holds the front sprocket on
chain
throttle cable
clutch cable
brake pads
stainless hub nuts and washers
front honda chain roller

Basically I got all the necessities, nothing shiny or fancy yet

I cleaned and painted the frame, airbox and tube, hubs, rear shock spring, foot pegs, front axle hub, rear axle, partially polished front fork tubes, gas tank. The only thing I didn't paint which would make the biggest difference in the world is the motor itself. That'll get done soon i hope! I'm too focused on getting it to run right now.

I will put my 20" rear 400ex tires on because those 22" are waaay too big. I also need a new front as that one has a hole. I'm debating on a new magnum easy clutch perch, and I need a new exhaust and thumb throttle. After those couple things I think it's ready to ride! I'm hoping after almost 2 years i might ride it for the first time this weekend!!! :beer

P.S. if anyone has an exhaust or thumb throttle hit me up!

[vartiak15]

how did u paint the spring? did u take it off? i need to no so i can do mine!

[AirManCam]

Looks good!

[vartiak15]

o and what type of paint did u use? spray can? or air compressor and air gun?

[kilabeez0]

i took the spring off. good luck unless u have a NON RUSTED shock assembly! i went thru like 3 sets until i found some where i could get the collar nut and lock nut off. when those things rust they do not come off no matter what. i soaked it, dremeled it, beat it with a hammer and chisel and couldn't get one to brake loose. sucked!

~~multiple coats of primer, followed with multiple coats of rustoleum metallic blue and clear coat.

[03 ORANGE SHEE]

i did that , it did not work for me!

[smokinp]

Did you sandblast the frame?

[kilabeez0]

no. i actually want a new frame, it looks like someone practiced their welding skills on this one. every joint is welded all around!

[leprogle]

I painted my frame the same color, I've been working on mine since the first of summer. always waiting for parts........
Hey, by any chance would you have a spare chain slider, in good condition?

[kilabeez0]

funny u should ask but no i dont. i'm missing the front slider and it's one of the LAST parts i just ordered from my local dealer....they just called me today and said it's discontinued :(

[BigGreenMachine]

ROFL at 03 Orange Shee

I can see and so far it looks great.