yamaha tri z hose routing

[ktmcrasher]

im just plumbing up the tri z but i lost all my pictures from when i took it to pieces & since this is the first ever build ive done im struggling to put the last few bits together so im wanting to show a few pictures and hopefully you guys can point me in the right direction

heres the first one...

what hose goes on this nipple on the left side case and where does it go, whats the route?
http://i1279.photobucket.com/albums/y521/krmcrasher/8C5A41BE-C155-411F-A839-46ECB13688F5-2399-00000447BCAE4D1E_zpse2b60130.jpg (http://s1279.photobucket.com/user/krmcrasher/media/8C5A41BE-C155-411F-A839-46ECB13688F5-2399-00000447BCAE4D1E_zpse2b60130.jpg.html)

[Bryan Raffa]

it goes 90 degrees back through the motor and the swing arm.. crank case vent.... I run mine out and down between the stator and sprocket .. zip tie it to frame ..

put black rtv on them stator wires right there.. water will git in there!

[ktmcrasher]

cheers raffa something like this?
http://i1279.photobucket.com/albums/y521/krmcrasher/97E6B9EC-F6AD-4385-92ED-F2DBF1726174-2399-000004545370FA55_zps4cc81296.jpg (http://s1279.photobucket.com/user/krmcrasher/media/97E6B9EC-F6AD-4385-92ED-F2DBF1726174-2399-000004545370FA55_zps4cc81296.jpg.html)

I've got a now stator and cable to put in and fiz that bit up

[ktmcrasher]

and the two hoses off the coolant bottle. ive got the top one running up the frame to the top of the rad?

what happens with the other one?
http://i1279.photobucket.com/albums/y521/krmcrasher/9703361A-D2CE-4A91-808F-223736131BA8-2399-000004546BA01C78_zps9c31fe32.jpg (http://s1279.photobucket.com/user/krmcrasher/media/9703361A-D2CE-4A91-808F-223736131BA8-2399-000004546BA01C78_zps9c31fe32.jpg.html)

[Bryan Raffa]

obviously thats a 86 ... this is 85 down the right through the loom with the in... out overflow i run to the rear .. so I dont get sprayed with hot coolant,, your tank vent comes up the left side and gets tucked in the rads between the frame and rad.. you gotta keep that in hose away from the pipe.. I run them both the same ..85/86 turn your head left on the last pic..

[ktmcrasher]

cheers raffia, so ive got the hoses the wrong way around then. i should have the top hose from the coolant bottle as the overflow.

the bottom hose goes up to the rad? sorry if im being daft but i really dont know!

[Bryan Raffa]

yes! you got it

[Bryan Raffa]

is that a 86 or 85 motor? i see your left case is a 85..

[ktmcrasher]

its 1rx on the right case? and its 6 speed... what makes it a 85 left case?

[Bryan Raffa]

bottom hole is not threded on a 85! BUSTED!!!!!!!!!!!!!!!!!!!!!!!!!!!!! both hole are threded on a 86.. :beer

[ktmcrasher]

whats the bottom hole? wheres the other hole? youd need to make me a drawing for me to figure out what youre talking about!

its a 1rx frame & right casing, it came with a 86 swinger 86 forks. the wheels were 85's though

[Bryan Raffa]

lol ... look...

[ktmcrasher]

ok i see what you're on about. will take a look at it, might just be a lump of powder?

[ktmcrasher]

Had a look this morning and I didn't want to ruin the finish but you might be right. Must have been replaced at some point.
Or it's a super rare 85.51... Prototype only one of its kind.

I'm going with the second theory! ;)

[Rigaman]

Only Raffa knows this stuff. I had no idea. I gotta go look at my 86 motors and check em. Thats pretty cool.

[Bryan Raffa]

and you can also run a 250r chain saver if you cut the top off and re drill some holes...:)